Wireteknik A210 Roll Swaging Machine 1.6-8mm Wire

A210 Roll Swaging Machine for 1.6 to 8mm Wire

A perfect machine for swaging on-site. Low weight and small outer dimensions makes it extremely portable.

Typical applications:

Standing rigging and lifelines for sailboats
Architectural, balustrades and railing
Scenographic use at theatres for hanging and supporting set pieces
Extensively used for on-site swaging of wire fall protection systems on roofs and buildings
Structural rigging for hang gliders and ultra-light airplanes
Oceanographers uses it for swaging winch wire ropes for their surveying instruments
Structural rigging for sail-roofs and sail-shades

Features:

Fully approved by Lloyd's Register of Shipping
Includes full sets of pullers
Dies and pumps sold separately

more info ↓ spec sheet Swaging Tools Wireteknik

Part	Description	Swaging Range Wire Ø mm	Length mm	Width mm	Height mm	Weight kg	RRP Inc VAT
WT-A210	A210 Swaging machine	1.6 - 8	TBA	TBA	TBA	9	POA
WT-A210-02	A210 Dies - 2.0/2.5mm (Pair)	2.0 - 2.5	-	-	-	-	POA
WT-A210-03	A210 Dies - 3mm (Pair)	3	-	-	-	-	POA
WT-A210-04	A210 Dies - 4mm (Pair)	4	-	-	-	-	POA
WT-A210-05	A210 Dies - 5mm (Pair)	5	-	-	-	-	POA
WT-A210-06	A210 Dies - 6mm (Pair)	6	-	-	-	-	POA
WT-A210-07	A210 Dies - 7mm (Pair)	7	-	-	-	-	POA
WT-A210-08	A210 Dies - 8mm (Pair)	8	-	-	-	-	POA

Wireteknik A210 operating instructions

Operating Instructions

· Use a pair of roller dies to fit the cable diameter

· Slip the dies onto the cogwheel synchronizing pins

· The arrows on the dies point in the direction of swaging

· Attach the terminal to the attachment fixture on the drawbar

· Adjust the length so the roller dies meet the terminal shank at the desired position

· Apply enough hydraulic pressure so the roller dies holds the terminal firmly

· Mark and insert the cable into the terminal throat

· Move the transparent protective shield into position

· Apply hydraulic pressure to draw the terminal between the roller dies

· As the roller dies rotate, they will press the terminal shank onto the wire rope

· Measure the diameter of the terminal after swaging, compare with the wire swaging dimensions list

Note: The swager is designed to reduce the terminal shank to required diameter in one pass. However dimension variations of terminals, cables or material hardness could make it necessary to pass the terminal twice.

When swaging solid rods, a special swaging compound must be used. After swaging wipe off the roller dies and swaging machine, apply a corrosion preventative.

The machines are designed to swage full steel wire rope or rod only.

Wire Swaging Dimensions

Wire Size mm	Diameter Before Swaging mm	Diameter After Swaging mm
1.6	3.94 - 4.06	3.40 - 3.50
2.5	5.41 - 5.53	4.70 - 4.82
3	6.22 - 6.35	5.44 - 5.56
4	7.42 - 7.54	6.23 - 6.35
5	9.00 - 9.12	7.83 - 7.95
5.5	10.72 - 10.84	9.35 - 9.50
6	12.42 - 12.54	10.95 - 11.12
7	14.18 - 14.30	12.50 - 12.70
8	16.01 - 16.13	14.07 - 14.30
9-10	17.73 - 17.85	15.70 - 15.90
11	19.63 - 19.83	17.27 - 17.47
12	21.32 - 21.44	18.82 - 19.05
12E	20.00 - 20.08	17.60 - 17.80
14	24.88 - 25.00	22.00 - 22.23
16	28.05 - 28.17	25.15 - 25.40
19	34.40 - 34.52	31.44 - 31.75
22	40.21 - 40.46	36.20 - 36.50
25	45.77 - 46.02	41.28 - 40.97
28	50.00	44.00 - 44.50
32	58.00	51.00 - 51.50
36	65.00	57.00 - 57.80
38 - 40	72.00	63.20 - 64.00